Product details
About this part
Cylinder head gasket 22311-2E000, also listed as 223112E000, 22311-2E070 and 22311-2E080, for the Hyundai and Kia 1.8 and 2.0 litre petrol engines in the Elantra, i30, i40, ix35, Sonata, Tucson, Creta, Sportage, Soul, Optima and Cerato from 2009 onwards.
The gasket is a multi layer steel item, normally three active layers with a thin stainless core, a folded stopper ring pressed around each combustion chamber, and a graphite or elastomer coating on both faces. The stopper ring is the part that takes the firing pressure and stops the layers from being blown apart at the fire ring; the coating is what seals the fine surface finish of the aluminium head and the block, which is why the surfaces are cleaned and checked flat rather than polished. Around the outside of the fire rings the same gasket carries the coolant transfer holes with their own sealing beads, the oil feed and drain holes for the head, and the chain or belt end passages, all in one piece.
Which engines. This number covers the 1.8 and 2.0 litre Nu and Theta II family used across a very wide spread of Hyundai and Kia models: the Elantra MD and AD, the i30 GD hatch and estate, the i40 saloon and wagon, the ix35 and Tucson, the Sonata YF and LF, the Creta, and on the Kia side the Sportage SL and QL, the Soul PS and SK3, the Optima and the Cerato YD and BD. The same casting and the same bore spacing are used in all of them, so a workshop covering both badges can hold one gasket instead of six.
Symptoms that bring one in. Coolant disappearing with no visible leak, bubbles or a fountain in the expansion tank when the engine is revved with the cap off, white exhaust smoke that smells sweet, a misfire on one cylinder immediately after a cold start that clears as the engine warms, or oil and coolant mixing into a brown emulsion. A compression test that shows two adjacent cylinders low usually means the fire ring between them has failed, and a chemical block test on the cooling system will confirm combustion gas in the coolant.
Fitting notes. These engines use torque to yield head bolts, so the bolts are replaced, not reused, and the final stage is an angle pull in the sequence from the manual. The head and block decks have to be straight and clean; a warped head is skimmed to the limit marked on the casting, and on a turbo or a high mileage engine it is worth checking the valves and guides while the head is off. Do not use gasket cement on a coated steel gasket. Fill with the correct coolant, bleed the system properly with the heater open, and recheck the level after the first warm up and cool down cycle.
Supplied individually, flat packed between boards so the fire rings cannot be bent in transit. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.