Product details
About this part
Front brake pad set 04465-26160, FMSI number D2088, is the heavy duty front pad for the Toyota Hiace III, IV and V vans and buses, the Dyna and Dyna 100 chassis cabs, the Granvia, and the Hilux V and VI pickups, from 1982 up to 2019 on the last Hiace IV buses.
This is a commercial vehicle pad, and it is built like one: a thick steel backing plate with rolled edges rather than a plain stamped flat, a tall friction block with a wear groove down the centre, and a set of stainless steel anti rattle shims and springs in the box. The compound is a low metallic formulation that keeps its friction level when the pads are hot from a loaded descent, and it is deliberately harder than a passenger car pad because these vans spend their lives at or near gross weight. The pad has a wear indicator tab on one of the four pieces and the set is two inner and two outer pads for a single piston sliding caliper on each side.
How they fail. Loaded Hiace and Dyna vans eat front pads faster than the service book suggests, and the first warning is usually a pedal that travels further before the brakes bite rather than an noise. Sliding calipers on these vans seize on the lower pin after a few winters of road salt, and then the outer pad wears at an angle, one end down to the backing plate while the other still has material. Drivers report a shudder through the steering wheel when braking from motorway speed, which is a warped disc or a pad that has bedded badly after a seized caliper was freed without cleaning the bracket. A pad with a cracked friction block or one that has come away from its plate must be replaced, and the disc thickness checked at the same time because these rotors are usually near their minimum by then.
Fitting notes. Crack the wheel nuts, chock the rear wheels, and lift the front of the van on a trolley jack with stands under the chassis rails. Take the caliper off the bracket rather than opening the hydraulic line, hang it from the spring so the hose is not stretched, and press the piston back with a proper spreader. File the bracket abutments flat, because the pad ears rust tight on these vans and a tight pad will drag and overheat. Fit the shims dry, no grease on the friction face, torque the bracket bolts to the manual figure, and check the disc run out if there was a shudder. Bed the pads with a series of firm stops from 60 km/h with cooling between, then check the fluid level.
Supplied as one axle set of four pads with shims, springs and wear indicator. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.