Product details
About this part
Ignition coil 06K905110C, also supplied as 06K905110G, 06K905110H and 06K905110K, is the coil on plug unit for the EA888 third generation 1.8 and 2.0 TSI engine in the Audi A3, A4, A5, A6, Q3, Q5, Q7 and TT, the VW Golf VII, Passat B8, Tiguan, Arteon, Beetle, Jetta, Polo GTI and Touran, the Skoda Octavia III, Superb III and Kodiaq, the Seat Leon and Cupra Formentor, and the Porsche Macan 2.0 TFSI, from 2012 to 2024.
This is the tall Gen3 coil, noticeably longer than the Gen2 unit it replaced, with the igniter built into the top of the body and a silicone boot that reaches down past the cam cover into the plug well. The secondary is wound for a higher output than the earlier coil because the Gen3 engine runs a lean stratified mode at light load and a wide plug gap, and the extra voltage margin is what keeps that mode stable when the plugs are half worn. The G, H and K suffixes are later revisions of the same coil and can be mixed on one engine; the letter only records a change of supplier or potting compound, not a change of electrical specification. Four coils are needed for a four cylinder engine and they are not handed.
How they fail. A Gen3 coil usually fails as a misfire under boost rather than at idle, so the car drives normally around town and then flashes the check engine light and cuts power when the driver asks for full throttle on a slip road. Codes are P0300 with one of P0301 to P0304, and on these engines the EPC light often comes on with them. The most common external cause is oil in the plug well from a hardened cam cover gasket, which softens the boot and lets the spark track down the ceramic. A coil that has been running with a plug gapped far too wide fails early because the secondary is working at its limit on every cycle. Heat soak after a long climb will make a marginal coil break down and then recover once the engine bay cools.
Fitting notes. Let the engine cool completely, because the boot sits close to the exhaust side on these cars. Remove the engine cover, release the coil harness by its latch rather than pulling the wires, undo the single fixing and draw the coil straight out with a twist. If the boot sticks, work it loose by hand; levering with a screwdriver cracks the cam cover. Inspect each well for oil before the new coil goes in, and fix the cam cover gasket if oil is present, otherwise the new coil will fail the same way. Fit with a thin film of dielectric grease, torque the fixing to about 8 Nm, and on an engine over 100,000 km replace all four together with new plugs.
Supplied as one coil with boot fitted, individually boxed. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.