Product details
About this part
Ignition coil 83502140, cross referenced with the GM numbers 10477208, 1115315 and 1115317, is the single distributor coil for the Daewoo Espero 1.5, 1.8 and 2.0, the Jeep Grand Wagoneer 2.8 V6, the Cadillac Cimarron, the Buick Century and the TBI 5.7 litre Chevrolet and GMC trucks and vans, from 1983 to 1999.
One coil serves the whole engine here, feeding the distributor through a single high tension lead, and it is mounted upright on a bracket against the body or the engine, with a four pin low tension plug moulded into the base instead of the two screw terminals used on older designs. Inside, a primary and a secondary winding sit on a laminated core in a sealed case, with the extra pins carrying the tachometer signal and the module ground back to the harness. The top cap has one deep socket for the HT lead, and the case is filled and sealed so it can live next to the exhaust manifold on a transverse engine such as the Espero where space is tight.
How they fail. The engine cranks and does not catch, or catches and dies the moment the key springs back, and a plug pulled from the king lead shows no spark or a weak orange one instead of a fat blue one. On the Espero and the GM trucks the usual cause is heat and oil: the winding opens or the internal insulation breaks down, and the coil reads open or way out of spec across the secondary. A corroded four pin plug gives the same no start and is often missed, so the connector should be looked at before the coil is condemned. A coil that is breaking down only when hot will start the engine from cold every morning and cut out after half an hour, and that pattern points straight at the winding rather than at the module.
Fitting notes. Disconnect the battery and pull the HT lead out by its boot. Release the four pin connector by pressing its retaining clip, then undo the bracket bolts and lift the coil out. Clean the bracket and the mating face, because the coil is earthed through it, and check the pins in the plug for green corrosion, replacing the plug body if they are eaten away. Fit the new coil the same way up as the old one, tighten the bracket, and push the connector home until it clicks. Check the resistance of the HT lead and the condition of the distributor cap and rotor before starting, since a worn cap will make a new coil look faulty. Start the engine, let it reach working temperature, and recheck for a stable idle.
Supplied as one coil with the four pin socket moulded in. Bracket and HT lead are not included. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.