Product details
About this part
Ignition coil 9220081067 is the round oil filled canister coil used on the distributor ignition of the older Brazilian and South American cars: the VW Gol, Santana, Passat B2, Saveiro, Voyage, Parati, Kombi, Apollo and Quantum, the Chevrolet Monza, Kadett, Ipanema and Chevette, and the Ford Escort III and IV, from 1976 to 1998.
This is the classic black cylinder that most of these cars left the factory with, and it is a very different part from a modern coil on plug. A single primary and a single secondary winding are wound on a laminated iron core inside a steel can filled with insulating oil, with a bakelite top cap that carries two low tension terminals and one deep high tension socket in the centre. The coil is clamped into a metal bracket on the inner wing or the bulkhead, and a single carbon core HT lead runs from the centre socket to the distributor cap. The oil is what carries heat away from the windings, which is why these coils are heavy and why a leaking one leaves an oily film on the bracket.
How they fail. The symptom is always the same whatever the badge on the bonnet: the engine turns over and will not fire, or it fires and dies as soon as the key is released, and there is no spark at the end of the king lead when it is held near the block. Heat and age crack the bakelite cap, the oil leaks out past the crimp at the base, and then the winding overheats and opens. A coil that has leaked leaves a smell of hot oil and a stain under the bracket, and one that is failing only when hot will run for twenty minutes and then cut out, which sends owners looking at the distributor and the fuel pump first. A coil with a cracked tower will track the spark down the outside of the cap and the engine will miss under load rather than not start.
Fitting notes. Disconnect the battery, pull the king lead out of the centre socket by the boot, and label the two low tension wires before they come off, because swapping them reverses the polarity and the engine will still run but poorly. Undo the clamp bolt, lift the coil out of the bracket, and clean the bracket and the earth contact underneath, since a rusty bracket is a common cause of a weak spark on these cars. Fit the new coil with the terminals pointing the same way as the old one, tighten the clamp so the can cannot rotate but is not crushed, and check the resistance of the HT lead before it goes back on. Set the points or check the trigger gap while the cap is off, then start the engine and confirm a steady idle.
Supplied as one coil with the top cap and terminals fitted. HT lead and bracket are not included. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.