Product details
About this part
Ignition coil F01R00A024, also sold as Q21-3705110, is the pencil type coil that pushes down onto each spark plug on the Chery Karry Youjin, Youyou, Youyou II and Youpai microvans with the 1.0, 1.1, 1.2 and 1.3 litre petrol engines built between 2009 and 2021.
On these three and four cylinder engines there is one coil per cylinder and no distributor, so the coil sits in the deep well in the middle of the cam cover with its boot wrapped around the plug insulator. The body is a slim resin tube roughly 90 mm long and 24 mm across, and the windings and the igniter are potted in epoxy so the whole unit can live in the heat and oil vapour above the head without a separate module. The secondary winding is wound to step the 12 volt supply up to around 30 kV, and the output reaches the plug through a spring loaded contact inside the silicone boot rather than through a short lead, which removes one connection that could arc. Primary resistance is around 0.5 to 1.0 ohm and the secondary reads several thousand ohms on a meter.
How they fail. The first sign is a misfire on one cylinder that shows as P0301 to P0304, a shaking idle and a van that pulls cleanly up to about 60 km/h and then stumbles on a hill. Because these vans are worked hard and often washed with a hose, the usual cause is water standing in the plug well: the coil boot seals against the cam cover, the well fills, and the high tension tracks down the outside of the boot to earth. Heat is the second cause, and a coil that has been cooked goes open circuit when hot and reads correctly again once it has cooled, which is why a cold resistance test can pass on a coil that is definitely faulty. A cracked boot or a plug that has been left loose also lets combustion gas past and coats the coil in black carbon.
Fitting notes. Work on a cold engine. Unplug the connector by squeezing its release clip, undo the single mounting bolt, and pull the coil straight up by the body, never by the wiring. Blow the plug well out with compressed air before the plug is removed, because grit dropped into the cylinder scores the bore. Check the plug gap and the plug condition while the coil is out, put a thin smear of silicone dielectric grease inside the boot lip, and seat the new coil until it bottoms on the plug. Tighten the bolt to about 8 to 10 Nm, no more, since the cam cover is aluminium. Replace the coil on the cylinder that the fault code names rather than all of them, but if two have failed within a year the rest are usually close behind.
Supplied as one coil with boot and spring contact fitted, individually boxed. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.