Product details
About this part
Ignition coil 90919-02212, also supplied as 88921337 and UF156, is the coil for the 5VZ-FE 3.4 litre V6 in the Toyota Land Cruiser 90 and Prado 120, the 4 Runner, Tundra, Tacoma, Hilux, Granvia and T100, from 1994 to 2005.
The 5VZ is a waste spark engine with three coils for six cylinders, so each coil has two high tension towers and fires a pair of plugs at once, one on the compression stroke and one on the exhaust stroke. The body is a rectangular block with the two towers at one end and a three pin connector at the other, mounted in a cradle between the cam covers and held by two bolts, with short HT leads running from the towers to the plugs. The windings are potted in epoxy inside a glass filled nylon shell, and the towers have deep silicone boots with spring contacts, because on these engines the coil sits high on the engine and takes the full heat of the exhaust manifolds on both sides.
How they fail. Because a coil fires two cylinders, a failure shows up as a misfire on both cylinders of the pair, which on the 5VZ means one and four, two and five, or three and six. The engine idles with a shake that a driver feels through the seat, loses power on a long climb and sets P0300 with two specific P030x codes. The most common cause on a Land Cruiser or Hilux is heat: the potting cracks around the towers and the coil arcs internally when hot, then works again after it cools, so the fault comes and goes for weeks. Water crossing a river, or a steam clean, gets into a cracked tower and kills the coil immediately. A resistance check across each pair of towers should read in the region of 10 to 15 kOhm; an open reading or a big difference between the two halves means replace it.
Fitting notes. Let the engine cool completely, disconnect the battery, and label the three HT leads before removing them, since the pairs are not obvious once the leads are off. Unbolt the coil cradle, lift it out, and look at the towers for cracks and at the boots for a white tracking line. Clean the cradle and the mounting face so the new coil sits flat, because a coil held at an angle will crack its potting. Fit new leads if the old ones are hard or show green corrosion at the terminal, apply dielectric grease inside the boots, and torque the mounting bolts to 8 Nm. Start the engine and check for a steady idle before the covers go back on, then clear the codes and confirm no misfire returns under load.
Supplied as one coil with two towers. HT leads and mounting cradle are not included. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.