Product details
About this part
Ignition coil 5149168AH is the coil on plug unit for the Chrysler Pentastar 3.6 V6 and the 3.0 and 3.2 versions of the same engine, as fitted to the Dodge Journey, Charger, Durango, Challenger and Avenger, the Chrysler 300C and Grand Voyager, the Jeep Wrangler JK, Grand Cherokee WK2 and Cherokee KL, the Fiat Freemont, the Lancia Thema and Voyager and the VW Routan, from 2008 to 2023.
The Pentastar runs six of these, one per cylinder, each pushed into the plug well on top of the left and right cam covers. The body is a slim tapered tower in glass filled nylon with the transformer and the igniter potted in a hard epoxy that is visible as a glossy black disc at the top, and the connector is a three pin bayonet fitting with a red locking slide that has to be pulled back before the plug will release. A ribbed silicone boot about 90 mm long sits at the bottom, with a stainless spring inside to bridge the gap to the plug terminal and a set of sealing rings to keep the well dry. The AI, AJ and AH suffixes are running changes to the potting and the boot material and any of them will run on the same engine.
How they fail. A single cylinder misfire with a P0301 to P0306 code and a flashing check engine light under load is the classic symptom, and on the Pentastar it is very often number three or number six because those wells sit under the plastic engine cover where water collects after rain or an engine wash. The boot carbon tracks down its outside and the spark jumps to the head instead of the plug, which leaves a fine black line on the silicone that is easy to see once the coil is out. Heat soak is the second cause: the coil works when cold and cuts out when the engine is hot, then reads correct resistance again after twenty minutes, so a bench test on a warm coil proves nothing. An oil leak from the cam cover gasket tube seals fills the well and softens the boot, and that must be fixed with the coil.
Fitting notes. Work cold, unclip the engine cover, and blow the plug wells out with air before anything is undone so grit cannot fall into the cylinder. Release the connector locking slide, then the tab, and pull the coil up by the tower rather than the wiring. Look at the old boot for the tracking line and at the plug for a wet or black insulator, because that tells you whether the fault is the coil, the tube seal or the plug. Put a thin film of dielectric grease on the new boot lip, push the coil down until it clicks onto the plug, and tighten the single bolt to 8 Nm. Clear the codes and drive the truck through a full load pull to confirm the misfire counter stays at zero.
Supplied as one coil with boot and spring contact fitted, in an individual box. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.