Product details
About this part
Fuel injector leak off pipe 1761934, also listed as BK2Q-9K022-AF and 9801197080, returns the surplus diesel from the four injectors of the Ford Transit 2.2 TDCi back to the tank, and it fits the Transit Mk7 and V363 vans, the Transit Custom and Tourneo Custom, and the Citroen Jumper, Peugeot Boxer and Fiat Ducato that share the Puma engine.
The pipe is a moulded nylon assembly rather than a set of loose hoses. Four short spigots push onto the leak off nipples on top of the injectors and are held by metal spring clips, and the spigots join a common rail of tubing that ends in a quick release coupling back to the return line. Nylon is used because it is unaffected by diesel and because it can be formed into the tight bends needed to run over the cam cover without kinking. Each spigot has an internal O-ring, and it is that ring, not the clip, that does the sealing; the clip only stops the spigot from backing off under vibration.
The leak off circuit looks unimportant but it is not. Diesel that passes the injector body is hot and aerated, and if the return is restricted the pressure behind the injector internals rises, which upsets the pilot injection quantity and shows up as a rough idle, a diesel knock at light load and long cranking when hot. A pipe that leaks also fills the recesses in the cam cover with diesel, which softens the cover gasket and gives the strong smell in the cab that drivers report before they see any drip on the ground.
How they fail. The nylon goes brittle with heat and age, and the usual break is at the base of a spigot where the wall is thinnest, or at the T junction where the four legs meet. A cracked spigot gives a slow weep that only shows as a damp patch and a diesel smell; a broken leg gives a hard start because the low pressure side draws air. On the V363 the pipe also rubs where it passes the engine lifting eye if the retaining clip has been left off during an earlier repair.
Fitting notes. Work on a cold engine and blow the area clean before opening anything, because grit under a spigot will hold the O-ring off its seat. Release each spring clip with a small pick, pull the spigot straight up and never sideways, and cap the injector nipples while the pipe is off. Fit the new pipe dry, with no sealant and no grease, seat each spigot until it clicks, and refit every retaining clip along the run. Run the engine and check each joint with a dry paper towel after five minutes, then again after a road test, because a weeping spigot often only shows once the engine is at full temperature.
Supplied as one complete leak off pipe assembly with clips. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.