Product details
About this part
Ignition coil 12570616, sold under the D510C and UF413 references, is the round coil used on the GM small block V8 family: the LS1, LS2, LS3, L76, L92 and the iron block truck engines in the Chevrolet Camaro, Corvette C6, Silverado, Avalanche, Suburban, Tahoe, Trailblazer and Express, the Cadillac Escalade and CTS, the GMC Sierra, Yukon and Savana and the Saab 9-7X, from 2002 to 2020.
Unlike a pencil coil this is a short fat cylinder about 60 mm tall with a flat top cap and a single high tension tower, and it works in wasted spark pairs: one coil fires two cylinders that are 360 degrees apart, so a V8 carries four of them on a bracket bolted to the valve cover, linked to the plugs by short HT leads. Two spade terminals on the top cap take the primary feed and the trigger from the ignition control module, and the windings sit in an epoxy filled plastic shell with a soft potting compound around the core to survive the heat that builds up under a tight engine cover. Because each coil serves two cylinders the secondary has to deliver twice as often as a single cylinder unit, which is why these are built with a heavier winding and run noticeably warm.
How they fail. A misfire on two cylinders at once, always a pair such as one and six or four and seven, points at one coil rather than at two plugs or two injectors. The engine shakes at idle, loses power under load and the scan tool shows the same misfire count on both cylinders of the pair. Heat and vibration crack the plastic tower where the HT lead pushes on, and once moisture gets in the spark runs down the outside and leaves a burnt track. On trucks that work in dust, the two spade terminals corrode green and the coil starts cutting out over bumps. A coil that has failed open reads infinite resistance across the secondary, but a coil that is only breaking down when hot will still pass a cold meter test.
Fitting notes. Disconnect the battery, then unclip the plastic engine cover and the bracket that holds the coils, marking the HT leads before they come off because the firing order makes them easy to swap. Pull the leads by the boot, never by the wire, and check each lead end for corrosion and for a broken core. Clean the bracket faces, fit the new coil, and tighten the two mounting bolts evenly so the potted body is not stressed. Use a little dielectric grease in each lead boot, push them on until they click, and make sure the coil to bracket ground strap is clean and tight, because a bad ground will kill a new coil in a few hundred kilometres. Clear the codes and road test with a loaded acceleration run.
Supplied as one coil with the top cap terminals protected. HT leads and bracket are not included. Twelve month warranty.
Frequently asked questions
Q: What kind of parts do you supply?
A: We are a trading company, auto parts supplier, and sourcing partner. We source fuel pump assemblies, filters, ignition coils, injectors, sensors, connector wires and other automotive parts through relevant suppliers. We are not a manufacturer; product and supplier details are confirmed for each quotation.
Q: Do you test all your goods before delivery?
A: Inspection and sample arrangements depend on the product and order. We can coordinate supplier documents, photos, samples, or pre-shipment inspection when included in the quotation. Please confirm the required scope before ordering.
Q: How long is the delivery time?
A: Lead time depends on supplier availability, product requirements, quantity, packing, and destination. The applicable lead time is stated in the quotation or order confirmation.
Q: What is your terms of packing?
A: Neutral packing is our standard: goods are packed in neutral white boxes and brown cartons. If you have a legally registered patent, we can pack the goods in your branded boxes after receiving your authorization letters. Above a minimum order quantity we also handle custom packaging and help with the design: printed color boxes, color labels, anti-counterfeit / security labels, and even small promotional items such as branded pens, mugs, baseball caps and T-shirts with your logo. Tell us your order quantity and requirements and we will confirm exactly what can be customized for your order.
Q: How can I get the warranty?
A: First of all, please take a photo when you receive the goods to confirm that the goods are in good condition, and then contact our sales, send the photo to us, we will record for you.