FOB Auto Parts Logo

Steering Column

Browse 7 Steering Column part numbers with OE cross-reference and fitment notes for passenger cars, SUVs, pickups and vans. Export packing available - send an inquiry for price and lead time.

Buying Steering Column by OE number

The steering column and shaft assembly carries rotation from the wheel down to the rack or the steering gear. On any car built after the mid-1990s it also carries the safety function: the shaft is collapsible, with a sliding section or a crushable tube, so that it shortens instead of spearing the driver in a frontal impact. Between the column and the rack sit one or two universal joints, and on an electric power steering car the assist motor is coupled to the same shaft through a damper or a worm drive.

This category carries 7 references, covering both the shaft itself and the joints that connect it. 45260-12750 is the intermediate shaft for Toyota applications, 45203-0K190 the steering shaft for Hilux Revo GUN125, and 45254-28040 the damper on the electric power steering motor shaft for Toyota and Lexus. 8L8Z-3B676-E is the lower shaft coupling U-joint for Ford Escape and Mercury Mariner, 815-914 and the 351-U joint cover the Ford F-750 cargo application, and KKY0133020A is the power steering knuckle joint for Hyundai and Kia. A further intermediate shaft assembly is listed for Toyota applications without a model restriction.

Four things have to match on a shaft. The spline count and diameter at each end, because a shaft that engages only part of the spline will strip under steering load rather than at the joint. The overall length, because the collapsible section is designed to sit at a specific installed length, and a shaft that is too long cannot be fitted without bottoming the sliding section. The type of joint at each end, since a yoke with a cross and bearing is not interchangeable with a rag joint or a rubber coupling. And on electric power steering cars, whether the shaft is the version that carries the assist motor coupling, because the manual shaft will physically fit but will not drive the motor.

The symptoms are a knock or a rattle felt through the wheel over rough ground, play at the wheel before the road wheels move, a steering wheel that is off centre after the shaft has been out, and on electric cars a steering assist warning. A clunk that happens when the wheel is turned while stationary is usually a worn cross in one of the universal joints; a clunk over bumps with the wheel still is more often the column bearing or the mounting bracket.

Order by the OE number together with the model and year, and state whether the car has electric or hydraulic assistance. Where the shaft has been removed for another job, it must go back in the same orientation, because the universal joints are phased and a shaft refitted a spline out puts the wheel off centre and can make the steering feel notchy.

Frequently asked questions

How do I know whether the knock is the shaft or the rack?

Hold the steering wheel still and have someone rock the front wheels by hand while you watch the shaft joints. Movement in the joint with the wheel still is the shaft. Movement felt at the wheel before the road wheels move, with no movement at the joint, points at the rack or the column.

Can I fit a used steering shaft?

Only from an identical model and assistance type, and never from a car that has been in a frontal impact, because the collapsible section may already be compressed. A compressed shaft is shorter than specification and will not protect the driver in a second impact.

Why is my steering wheel off centre after replacing the shaft?

Because the shaft was engaged one spline out, or because the universal joints were not phased correctly. Correct it by moving the shaft one spline rather than by adjusting the tie rods, otherwise the rack is left off centre and the turn angle is uneven left to right.

Does the shaft need to be replaced when the U-joint is worn?

Not always. Where the joint is a separate service part it can be replaced on its own, but on many assemblies the cross is staked in and the complete shaft is the service item. The listing states which form it is.

Do you confirm the reference before shipping?

Yes. Send the number from the old shaft or joint, the model and year, and whether the car has electric assistance. We confirm against the reference you supply and state it on the quotation rather than shipping a shaft on a model name alone.

Send your OE list for a quotation

Tell us the OE numbers, quantities and destination port. We confirm fitment against your references and quote with export packing options.